I’ve Been Stuck In Trial And Error Hell

Concept #1

My first thought was clearly to place the sunshine again collectively utilizing the primary concept that I had after I simply assembled the lampshade rings a few weeks in the past. That first time, I used beading wire and screw-on crimp beads, each of that are used to make jewellery.

So I began off utilizing that course of to re-assemble all the rings as soon as I had all the painted spoons hooked up to the rings. However the extra rings I assembled, the much less assured I grew to become that the wire and crimp beads on the high would maintain the load of all the rings with the load of the spoons added. I had about 5 rings assembled, beginning on the high and dealing my manner down, after I determined to desert that concept and discover one thing sturdier to carry the lampshade rings collectively.

Concept #2

Since I had hooked up all the spoons to the lampshade rings utilizing bounce rings, and I had loads of these left over, I had the thought to make use of tiny jewellery chain and bounce rings to connect the rings to one another.

That appeared like an important thought, besides that I’d get just a few chains/rings hooked up, after which a series would slip out of a bounce ring and the entire thing would go askew. I’d get that one put again on, just for one other chain to slide out of one other bounce ring, and the entire thing would go askew once more. The issue was clearly that the chain was too skinny, and I couldn’t get the bounce rings closed sufficient for the chain to cease slipping by means of the break within the bounce ring. So I wanted a brand new thought.

Concept #3

I wanted one thing easy, and my thoughts instantly went to S-hooks. How straightforward would that be?! I couldn’t think about something being simpler or quicker! Or so I believed. I headed to Dwelling Depot and purchased sufficient of those 1.25-inch S-hooks to assemble the entire thing. I had such excessive hopes.

I imply, simply have a look at how straightforward! Slip an S-hook onto two lampshade rings, use pliers to crimp the hooks in order that they might clamp across the lampshade ring wire, and taa-daa! Performed! Proper? It’s fast and easy!

Besides that it was too quick. It made every row of spoons cowl over the following row of spoons manner an excessive amount of in order that solely about half (or possibly much less) of the spoons on the following row confirmed.

And I received at about 5 lampshade rings assembled, second-guessing my resolution your entire time, earlier than making the choice that they had been simply too quick. So I then needed to disassemble all of these rings. And eradicating these S-hooks as soon as they had been crimped onto the lampshade rings wasn’t straightforward!

Concept #4

I simply wanted to provide you with a method to lengthen the S-hook a bit bit, so then I attempted extending it with a bounce ring. And I may have used a bounce ring on high and on backside to increase it even additional.

However earlier than I received too far with that, I made a decision to desert the thought of bounce rings altogether. They’re nice for jewellery, and so they’re nice for holding every particular person (and really light-weight) spoon to the lampshade ring. However they’re simply not made for holding an excessive amount of weight. And I didn’t really feel assured sufficient in them to belief the meeting of your entire pendant mild to small bounce rings made for jewellery making.

Concept #5

So I moved on to my subsequent thought — smaller S-hooks. I believed that these could be simpler to work with, and simpler to crimp onto the lampshade rings, than the larger 1.25-inch S-hooks.

So I put two of them collectively, and…

…not solely was it ugly, however it was too quick. After all, I ought to have recognized that. If the 1.25-inch S-hook was too quick, then two 3/4-inch S-hooks put collectively are going to be too quick since that’s actually the identical size. 😀

Concept #6

Then I attempted utilizing one 1.25-inch S-hook and one .75-inch S-hook. The size was good. I’d say it was excellent. However getting these S-hooks crimped to one another, after which crimped onto the lampshade rings was not straightforward, and so they simply didn’t look good. It seemed huge and hulking, and I needed one thing smaller that wouldn’t look so cumbersome.

Concepts #7 and #8

So again to Dwelling Depot I went, and this time I purchased the smallest chain that they had with hyperlinks that might be pulled aside (i.e., I couldn’t use chain with the hyperlinks soldered closed). That is what that they had.

I had excessive hopes. However the issue is that if I used three hyperlinks, it was too lengthy…

And if I used two hyperlinks, it was too quick.

Two hyperlinks received me proper again to the identical size as one massive S-hook.

I actually wanted 2.5 of these hyperlinks. That may be the proper size, however I didn’t need to reduce these hyperlinks in half. Regardless that it’s attainable to chop them in half due to how they’re made, and simply use 1/2 of a hyperlink, chopping it in half seemed ugly. I simply didn’t need to try this. So I headed again to the drafting board.

Concept #9

I headed again to Michael’s one final have a look at any choices that they had, and I bought these cut up rings. Cut up rings are like keychain rings, however these are for jewellery, so that they’re fairly small.

I had the concept that I may principally create my very own chain out of cut up rings. And since no bounce rings could be used, and cut up rings are way more safe, I used to be certain this is able to work. So I purchased all that they had, and headed residence. However I rapidly realized that this concept was a bust. I sat there for a superb 5 minutes simply attempting to get two cut up rings put collectively (and destroyed my fingernails within the course of), however the cut up rings had been so tight that I by no means even received two put collectively, a lot much less sufficient to kind a series. So there’s no manner I used to be going to sit down there and attempt to assemble sufficient to place your entire mild collectively. I don’t assume there’s any manner I may have gotten a kind of cut up rings across the lampshade ring wire.

Concept #10 — THIS ONE WORKED!

Then it got here to me. The cut up rings had been in regards to the dimension of 1/2 of a hyperlink of the small chain. And a pair of.5 hyperlinks of that chain could be the proper size. So I took two particular person hyperlinks of the chain, and assembled them with a cut up ring within the center, and that is what I had…

And…IT WORKED!!! Y’all, in the event you heard the faint sound of somebody crying tears of pleasure and reduction round 5:30pm yesterday, that was me. It took me ten tries, however I lastly…FINALLY…discovered one thing that may work. It was sturdy, so there was no manner it was going to come back aside on me. And it was the appropriate size. It’s not the appropriate shade, however that’s nothing {that a} small paint brush and a few liquid gold gilding can’t repair.

So I received 9 rings assembled to one another earlier than I went to mattress final evening, and as an alternative of attaching every ring to the following ring in 4 locations, I made a decision to do eight. It makes the entire thing a lot extra secure. I don’t have them lined up but as a result of I’m nonetheless assembling every part. However as soon as I get the entire thing assembled, I’ll return and line every part up good, after which begin placing the spoons in place.