Studio Desk Makeover – FINISHED! (Plus, Adding Wood Veneer To A Desktop)

Right here’s a have a look at how the desk taken care of I constructed it a couple of years again…

And right here’s what the desk seems like now…

In my final submit on this venture, I had completed the desk base. As soon as it was all painted one shade, it seemed like this…

So I minimize strips of 1-inch lumber, ripped to the right width utilizing my desk noticed in order that these strips would cowl the sting of the desktop. After which I nailed these strips onto the sides of the desktop utilizing 16-gauge, 1.5-inch nails.

Right here’s what it seemed like with the strips hooked up to all 4 sides…

Since all of this might be hidden below veneer, there wasn’t any have to miter the corners…

However only one strip wasn’t sufficient. That solely prolonged all sides a further 3/4-inch, and I wanted double that. So I added a second strip to every facet…

Once more, I didn’t trouble mitering the corners. However I did use my sander to ensure the corners the place the boards met had been very clean.

Right here’s what it seemed like with two strips hooked up to all 4 edges.

Subsequent, I gave the highest a fast sanding with 100-grit sanding discs, not solely to take away the paint and glue that had been on the desktop, but in addition to ensure the transition from the unique desktop to the newly hooked up strips on the sides was very clean with no excessive spots.

Then I used to be prepared to connect the veneer. I used a 4′ x 8′ sheet of quartered walnut veneer for this desktop. I began by inserting the sheet flat, after which reducing off a 2.25-inch strip from the suitable finish of the veneer. This piece could be for the suitable edge, however I didn’t wish to connect it simply but.

Subsequent, I minimize off a 2.25-inch strip on the entrance fringe of the veneer. That is the piece I glued on first. I hooked up the veneer utilizing Weldwood Contact Cement and a 6-inch curler for clean surfaces. I all the time put two coats of contact cement on each surfaces (the again of the veneer and the sting of the desk on this case), letting it dry fully between coats, after which letting it dry fully earlier than attaching the veneer. I hooked up the strip of veneer in order that it caught up above the desktop about 1/4-inch. No less than, that was the aim. It wasn’t excellent. As soon as it was hooked up, I used a flooring curler to ensure it was securely hooked up, after which used a utility knife with a model new blade to chop off the surplus 1/4-inch (or extra) from the highest fringe of the veneer.

The following piece that I hooked up was the highest. After coating each surfaces with two coats of contact cement and letting it dry, I positioned strips of scrap wooden on the desktop about six inches aside, spanning the entire desktop, after which positioned the veneer on high. These strips saved the veneer from touching the desktop earlier than I used to be prepared. I lined up the suitable edge and the entrance edge in order that the veneer overlapped about 1/4-inch, after which pressed the veneer into place from proper to left, eradicating one strip of wooden at a time and urgent the veneer into place. After which I used my utility knife to trim the suitable edge and the entrance edge.

The again edge and the left edge had a complete lot of overlap. I wanted to watch out in reducing off this extra as a result of, as a lot as I may, I needed to scale back waste in order that I may get the grain on the sides to line up with the highest as a lot as potential. And if I minimize away an excessive amount of, and had an excessive amount of scrap between the items, the grain wouldn’t line up.

I ended up shedding about 1/2 inch of veneer between the 2 items as soon as I fastidiously minimize off the surplus after which trimmed each…

You’ll be able to see right here that after I minimize off the massive piece of extra veneer from the left facet, trimmed the veneer on the desktop, after which hooked up the veneer to the left edge, the grain nonetheless matched up fairly properly, regardless that I misplaced about 1/2-inch of veneer in that course of.

Additionally, sanding makes all of the distinction relating to working with veneer. That is one purpose I really like working with actual wooden veneer. For instance proper after attaching the veneer to the left facet and trimming off the surplus from the highest edge, look how tough it seemed…

However after burnishing it down a bit extra, after which sanding that nook, that is the way it seemed…

After which as soon as I received the surplus veneer trimmed off of the underside, that is how that left edge turned out…

And right here’s a have a look at the completed high, and the 2 completed edges (left edge and entrance edge), at that time…

Subsequent, I added the suitable edge piece. This was the primary piece I minimize from the large piece of veneer, however I wanted to connect the highest earlier than including this edge. It’s rather a lot simpler to match up a small piece to a big piece that’s already in place moderately than making an attempt to match up a big piece to a small piece that’s already in place.

After which lastly, I hooked up the again edge (i.e., the desk chair facet).

And right here’s the way it seemed as soon as every part was trimmed and sanded.

And right here’s a greater view of the desktop. Quartered veneer usually has attention-grabbing patterns in it, and this piece had fairly a couple of. These don’t trouble me, however simply notice that in the event that they do trouble you, and also you’re wanting to make use of veneer on a venture, you may wish to search for a special minimize of veneer.

To seal the desktop, I used the identical product that I used on the entire walnut in our lavatory — Rubio Monocoat Oil Plus 2C in Pure (affiliate hyperlink). These things is AMAZING. It’s an oil plus a hardener, and it’s extremely sturdy. All the walnut in our lavatory seems simply nearly as good at this time because it did the day I completed it, and I’ve by no means needed to recoat.

After mixing the 2 components collectively in a 1:3 hardener-to-oil ratio, I wiped it on with a paper towel. Simply notice that that is NOT the right method to do that. It’s a lot simpler to use with one thing like a type of white spongy applicator issues that gained’t take in (and waste) numerous oil, and that gained’t depart behind little bits of white within the oil. However I didn’t have a type of applicators, so I simply used a paper towel. It wasn’t supreme, however I made it work. Right here’s the distinction that the oil made within the shade…

I wiped oil onto the entire floor, let it set a couple of minutes, after which used a clear white rag to buff the complete floor. It leaves a stunning matte end on the wooden.

And right here’s the oiled desktop. Isn’t that fairly?! I really like walnut. I simply love how deep and wealthy the colour is with out being too darkish.

Right here’s a comparability of the scrap piece of unfinished veneer on high of the oiled veneer.

And with that, the desk was carried out.

I’m so happy with how this desk turned out. I really like being within the kitchen and searching into the studio to see a glimpse of the desk, pendant gentle, and pink cupboards. Now I simply want my crimson velvet chair!

My mother came to visit yesterday, and when she noticed the desk with its new high, she mentioned, “Wow! I knew it was going to be fairly, however I didn’t comprehend it was going to be THAT fairly!” 😀

I’ve to agree along with her. I knew it could be fairly, and I may make it work. However I believe the ultimate look far exceeded my expectations.

And I simply love sitting at this desk, with my arms resting on this clean wooden desktop, and searching as much as see that stunning pendant gentle. I’ll be spending many hours right here, and it’s simply excellent.

In any case was mentioned and carried out, I ended up not including drawers to the desk. I had one drawback after one other with that plan, so I ended up carrying the highest trim all the way in which throughout the again (chair facet) of the desk, after which I wrapped the opposite trim round similar to I did on the underside under the leaf panel.

That offers it a completed search for now, whereas additionally permitting for the opportunity of including drawers later if I modify my thoughts.

Anyway, I’m so happy with how this turned out. I used to be very pleased with the unique desk for a few years. It was a very good, sturdy, helpful, utilitarian desk.

However I believe the brand new seems is so significantly better. It matches the studio so significantly better, and it’s rather more “me”.

In order that’s yet one more huge venture checked off of my “to do” checklist for this room. I’ve only a few extra, together with some electrical work, some trim and door casings, and reupholstering my desk chair.

After which getting this room all cleaned up and arranged goes to be fairly the job. The considered tackling that job is a bit overwhelming proper now.

However not less than this one is completed. And I’m simply so pleased with the way it turned out!