How To Build DIY Window Flower Boxes (Another Workshop Project Done!)

My DIY window containers for the workshop are finished! Y’all, this is perhaps my favourite undertaking but. I imply, I notice that every one of those tasks are working collectively to create the look I needed. Had I simply plopped some window containers onto this workshop in its authentic state and known as it good, they wouldn’t have finished a lot for the constructing on their very own. However of all of the modifications I’ve made up to now, that is the one I used to be essentially the most enthusiastic about. Simply look how cute these are.

And I’ll admit that I crammed them with faux vegetation…for now. I needed to see what they seem like crammed, nevertheless it’s winter. And sure, although I’m in central Texas, we do nonetheless form of have a winter. It’s been getting under freezing at night time, so I didn’t wish to purchase actual vegetation just for them to freeze to dying. So for now, the faux vegetation will do. As soon as spring hits, my plan is to show these into self-watering planters and plant some actual vegetation in them.

So let me present you the way I constructed these DIY window flower containers. That is such a easy undertaking that just about anybody can do. You may see your complete course of right here:

To construct the fundamental field, I used 1″ x 8″ PVC boards. After measuring my window, which was 32 inches vast, and measuring the area between shutters, which was virtually 38 inches, I made a decision to construct these containers 34 inches vast to depart sufficient room for the trim that I’d be including later. So for every field, I reduce one backside piece to 32.5″, two finish items to 7.25″, and two items for the back and front to 34″.

Since these are PVC boards, I used PVC glue to stick the boards to one another and nailed the boards along with 16-gauge 1.5-inch nails. I began by attaching the ends to the underside piece.

And as soon as each ends have been connected, it appeared like this…

Then I positioned the underside/ends portion on its facet, and put PVC glue on the perimeters of the underside/ends, after which put extra glue across the ends and backside of the entrance piece. When working with PVC glue, you must work shortly since you need the glue to be actually moist while you put the items collectively. And PVC glue dries pretty shortly.

As quickly as I utilized a liberal quantity of PVC glue to these areas, I put the entrance board in place and nailed it on all the best way across the sides and backside.

I repeated that course of for the again piece, after which I had a really primary, no frills, plain field.

First, I trimmed out the highest fringe of the field utilizing a PVC molding known as shingle molding. The supposed goal of shingle molding is to be used on the fascia boards of a home slightly below the shingles. However it’s such a reasonably molding that I take advantage of it as a multi-purpose trim.

Right here’s a better take a look at the shingle molding…

To connect the entire trim, I used PVC glue and adopted up with 18-gauge 1-inch nails. I solely utilized the trim to a few of the 4 sides of the field since I wanted the again to be utterly flat to suit towards the constructing. So utilizing my miter noticed, I reduce the entrance piece mitered on each ends.

After which I reduce the facet items mitered on the entrance corners, and reduce straight alongside the again edge the place it might meet the constructing. In case your mitered corners aren’t excellent, don’t fear about that. That’s what caulk and exterior wooden filler are for. 😀

Right here’s a take a look at the field with the highest trim connected. You may already see how the trim actually attire up the plain field.

To trim out the underside fringe of the field, I used PVC base cap molding. The supposed goal of base cap molding is to decorate up plain baseboards (i.e., to cap off plain baseboards), however once more, I discover myself utilizing base cap molding for as a common goal trim as a result of it’s so versatile. Right here’s a better take a look at base cap molding…

Utilizing my miter noticed, I reduce and utilized that molding to the field in the identical approach I did the shingle molding across the prime.

And with the bottom cap molding on, the field was actually beginning to seem like a reasonably planter.

At this level, I made a decision to hold these containers on the constructing. And since I work alone, I needed to make this so simple as doable. I went forward and began three screws by the again of the field. I used three 3-inch exterior screws for this.

After which I held the field up in place and screwed into to the siding. This course of was extremely straightforward with the kind of siding I’ve on this constructing. You probably have stone, it’s going to take a bit extra work that may require a masonry drill bit and masonry screws. And if in case you have lap siding, the field would possibly have to be shimmed to get it to hold straight relatively than at an angle. You’ll must assess what you want on your specific state of affairs.

First, I positioned the corbel contained in the field and marked the width of the corbel with a pencil to find out the place the screws wanted to be positioned. After which I began 4 screws.

After which I used a liberal quantity of PVC glue on the highest of the corbel and the underside of the field, and held the corbel in place whereas screwing it to the field with these 4 screws I began contained in the field. And right here’s a take a look at the field with each corbels connected.

And eventually, I needed to trim out the corners of the field in order that the reduce edges of the 1″ x 6″ boards of the field didn’t present. I used some scrap 1″ x 2″ PVC boards that I had available, and I reduce these down utilizing my miter noticed in order that I had skinny strips that have been 3/4″ vast and slightly below 1/4″ thick. In case you don’t have a desk noticed, you should buy skinny PVC lattice or display screen molding for this. And I connected these items vertically on the entrance corners and alongside the again the place the field met the constructing.

And with that, the field construct was finished. I nonetheless must caulk and paint (similar to the skirting and the entrance steps) however the climate hasn’t been cooperative recently. So I’ll want to attend till we now have a couple of sunny and dry days to do all of my caulking and portray. However I’ll be portray all of it white anyway, so it received’t change the look a lot, if in any respect. However for now, I’m completely having fun with the look of my uncaulked, unpainted flower containers.

For now, I went forward and drilled two small drainage holes on the underside of every field. I’ll have the ability to fill these holes fairly simply with caulk as soon as I get able to convert these containers to self-watering containers within the spring. However for now, with the entire rain in our forecast over the subsequent week (at the very least), I didn’t need these filling up with rainwater.

I simply love how these turned out. I believe they’re the proper contact for my workshop, and so they add some a lot wanted dimension to the in any other case very flat constructing.

And whereas faux vegetation aren’t supreme, I’m glad to have them full of one thing that offers some coloration and curiosity to the containers.

I spent about $200 on faux vegetation for 4 containers. I don’t suppose that’s too dangerous. I plan to maintain them and use them every winter, if essential. I don’t need empty window containers. 😀 I take advantage of a mix of vegetation from Passion Foyer, which I bought throughout a 40% off sale, plus these from Amazon (all affiliate hyperlinks): pink flower stems, boxwood stems, and weeping willow stems. These are those I selected, however there are a ton of different choices from that firm on Amazon.

So, that’s it! One other undertaking marked off of my checklist for the 12 months. And I couldn’t be happier with how they turned out.

I did make 4 flower containers in order that the again home windows (the home windows which are seen from the road) may look cute, too. However what a large number this facet seems to be like with that soiled skirting. However a bit a part of the answer for that downside is within the works, and I’ll share that tomorrow.

For now, I simply attempt to look previous the filth and admire my cute little window containers. 😀